- In-situ density by sand replacement method using large / small pouring cylinder
- Dry density – moisture content relationship(MDD-OMC)
- Maximum and minimum index density
- Moisture content
- Bulk density and dry density determination
- Shear test
- Swell Pressure
- Plate load test
- Electrical conductivity/resistivity determination
- Sulphate content (Acid/Water Soluble)
- Organic Matter Content
- Gypsum Content
- Materials Finer than 75µm Sieve (Fines Passing No. 200) in Mineral Aggregates by Washing
- Specific gravity & water absorption of fine & coarse aggregates
- Sieve Analysis (Aggregate)
- Particle density & water absorption
- Flakiness Index of aggregates
- Aggregate crushing value
- Ten percent fines value
- Soundness of aggregates by the use of sodium sulphate / magnesium sulphate
- Organic Impurities
- Full chemical analysis of rock
- Los Angeles abrasion Value.
- Petrographic examination
- Rock Grading
- Lightweight pieces
- Uniaxial compressive strength
- Bitumen content determination by extraction method
- Rate of spray/application
- Marshall density
- Asphalt Mix Design
- Loss of stability of bituminous mixture
- Stability and Flow of bituminous mixture
- Ductility
- Penetration
- Softening point
- Saybolt furol/universal viscosity
- Sampling, Slump, Temperature of fresh Concrete
- Concrete setting time (initial/final)
- Water-cement ratio (Fresh Concrete)
- Compressive strength of concrete cubes, Cylender
- Flexural strength of concrete beam
- Initial surface absorption test (ISAT)
- RCPT
- Cement Setting time
- Cement Fineness (specific surface – Blaine), Soundness, Consistency, Setting time, Activity index, Compressive strength
- Full Physical Analysis of Fly ash, Microsilica, Admixture
- Masonry Blocks - Compressive Strength, Dimension , Water Absorption
- Rebar - Tensile strength and elongation , bend, rebend
- Particle size distribution by sieve analysis, Hydrometer analysis, Uniformity coefficient , Soil classification
- Liquid limit ,Plastic limit & plasticity index determination
- California Bearing Ratio (soaked/ unsoaked)
- Linear shrinkage test
- Particle density determination
- In-situ CBR
- Consolidation
- Dynamic Cone Penetration Test (DCPT)
- Thermal conductivity/ Resistivity in soil
- Chloride content (Acid/Water Soluble)
- Total Soluble Salts
- Carbonate content
- Clay lumps and friable particles
- Determination of Bulk density
- Crushed Face Analysis
- Shell content determination
- Elongation Index of aggregates
- Aggregate impact value
- Point load index test
- Sand equivalent value
- Potential Alkali Reactivity
- Methylene blue absorption
- shape index
- Polished stone value
- Moh’s hardness
- Drying shrinkage
- Unconfined compressive strength
- Thickness and density of compacted bituminous mixture
- Particle size analysis of extracted aggregate
- Theoretical maximum specific gravity & density of bituminous paving mixture
- Index of retained strength
- Percentage Voidage in compacted bituminous paving mixture/ Percentage of voidage at refusal
- Coating & stripping test of bitumen aggregate mixture
- Specific gravity
- Solubility
- Flash point
- Kinematic viscosity
- Air content in fresh concrete
- density of fresh concrete
- Differential temperature measurement of mass concrete pour
- Tensile splitting strength
- Water absorption of hardened concrete
- Water permeability (depth of penetration)
- Chloride Migration
- Full Chemical Analysis of Cement
- Full Chemical Analysis of Fly ash, Microsilica, Admixture
- Mix design and Laboratory Trial Mix
- Tiles - Compressive strength, Transverse strength, Water absorption, Density, Modulus of rupture, Flexural strength, Dimension, Resistance to stain
- Full Chemical analysis of Steel
